2020-2024 Ford PIU 9.26" Dash Display Screen Kit "Beta" - DEV BACKERS
Custom ATO-Auto Designed & 3D Printed Display Screen Kit, Fully Assembled w/ Display, for 2020-2024 Ford Police Interceptor Utilities *The AMERICAN FLAG will NOT be present, it was strictly a test*
DEV BACKER DEAL - By Purchasing you will secure fixed discount for pre-order Beta units or final release versions. Your $100 deposit will be honored as a one time, $125 coupon off the Beta, Late Beta, or Official Launch. These Coupons are good for 1 purchase through December 31st, 2026.
This Dash Display Screen Kit makes adding modern tech easier than ever before. Transform your 2020-2024 Ford Police Interceptor Utility dash into a modern interface utilizing a sharp, responsive 9.26" display. Installation requires little effort, only involving limited tools and knowledge. Designed to fit using OEM mounting tabs, bolt, and maintain a sleek, refined appearance with the factory dash once installed.
Made with high-quality PC-CF plastic, UV resistant and temperature rated over 120°C (248°F). All components backed by a full 2 year Replacement Warranty, starting the day the unit is shipped.
Included:
- Custom ATO - Auto 3D Printed Dash Screen Display Housing for 2020-2024 Ford Police Interceptor Utility
- Krunia 9.26" Display 1600*600 Resolution
- Original Krunia Packaging and Materials
- Pre-Installed MRGLAS 10ft USB-A to 90 Degree USB-C
- Anker 320 Car Charger(2 USB-A Sockets)
- Custom ATO - Auto 3D Keychain
- Packing Slip
Fitment:
- 2020-2024 Ford Police Interceptor Utility
Pre-Order Availability Timeline:
Pre-Order launch dates and ship dates shown below. Each Pre-Order drop will close when sold out. Beta feedback may change dates.
Orders Open March 30th, 2026 -> 10 Early Beta Units, $75 Off during Launch Sale -> Ships by April 27th, 2026
Orders Open April 20th, 2026 -> 10 Late Beta Units, $50 Off Final Beta Sale -> Ships by May 18th, 2026
Orders Open May 25th, 2026 -> 15 Generation 1 Units, $25 Off Official Launch -> Ships by June 22nd, 2026
FAQ:
Is there a physical "Off" button?
- There is a physical Off button on the top of the display. The display also has a digital Off button.
How does the display get installed?
- Remove the 2, 7mm top dash tray bolts, then lift the OEM tray out, be aware there are 5 clips that will also be retaining the dash tray as you lift up. Release the trim just above the ignition to allow you to pull the the OEM Display/Vent Bezel toward the rear of the car. It is only held in by clips and can be removed by pulling from the vents and working your way around to release the clips. Once released, disconnect the rear connectors attached to the display, terrain, and perimeter alert button if equipped. *If you struggle to get the Vents to clear, put the vehicle in drive to move the column shifter out of the way, don't forget to put it back in park. Next, place the begin to route the USB power cord down through the dash, utilizing the hole nearest to the windshield to begin guiding the cord through. Route the cord towards the passenger side glovebox. Open your glovebox and release the 2 locking tabs to allow it to drop down further. Grab the cord and feed it down to the footwell. You may now guide it towards the center console area easily and connect to a 12v power source of your choosing. Connect to the factory cigarette plug using the included car charger or factory USB outlet. Note: Use Forscan to program the Power Point shutdown timer to be killed when ignition is off and after a door is opened. Turn the vehicle on to send power to the display and test for function. Replace all trim, glovebox, and finally bolt the Display Kit down using the OEM 7mm bolts. Turn the vehicle on to send power to the display. Connect the Display to your phone, the audio setting on the display allows your Bluetooth audio to be sent to the vehicle directly. Your installation is now complete.
DEV BACKER DEAL - SELECT GROUND SHIPPING