2020-2024 Ford PIU 9.26" Lock-On Grid Dash Display Screen Kit "Beta"
Custom ATO-Auto Designed & 3D Printed Lock-On Grid Display Screen Kit, Fully Assembled w/ Wireless Apple CarPlay/Android Auto Display, for 2020-2024 Ford Police Interceptor Utilities.
This Dash Display Screen Kit with Lock-On Grid(L.O.G.) makes adding modern tech easier than ever before. Transform your 2020-2024 Ford Police Interceptor Utility dash into a modern interface utilizing a sharp, responsive 9.26" wireless Apple CarPlay and Android Auto display. Installation requires little effort, only involving limited tools and knowledge. Designed to fit using OEM mounting tabs, bolt, and maintain a sleek, refined appearance with the factory dash once installed. Use the included L.O.G. to transfer over Bulletpoint Mounting Solutions accessories.
Made with high-quality PC-CF plastic, UV resistant and temperature rated over 120°C (248°F). 11ga, Powder Coated Rolled Steel is used to manufacture the Lock-On Grid. All components backed by a full 2 year Replacement Warranty, starting the day the unit is shipped.
Included:
- Custom ATO - Auto Lock-On Grid Attachment Plate
- Custom ATO - Auto 3D Printed Dash Screen Display Housing for 2020-2024 Ford Police Interceptor Utility
- Krunia 9.26" Wireless Apple CarPlay and Android Auto Display 1600*600 Resolution
- Original Krunia Packaging and Materials
- Pre-Installed MRGLAS 10ft USB-A to 90 Degree USB-C
- Anker 320 Car Charger(2 USB-A Sockets)
- Custom ATO - Auto 3D Keychain
- Packing Slip
Fitment:
- 2020-2024 Ford Police Interceptor Utility
Pre-Order Availability Timeline:
Pre-Order launch dates and ship dates shown below. Each Pre-Order drop will close when sold out. Beta feedback may change dates.
Orders Open April 3rd, 2026 -> 10 Early Beta Units, $75 Off during Launch Sale -> Ships by May 1st, 2026
Orders Open April 20th, 2026 -> 10 Late Beta Units, $50 Off Final Beta Sale -> Ships by May 18th, 2026
Orders Open May 25th, 2026 -> 5 Generation 1 Units, $25 Off Official Launch -> Ships by June 22nd, 2026
FAQ:
Is there a physical "Off" button?
- There is a physical Off button on the top of the display. The display also has a digital Off button.
How does the display get installed?
- Remove the 2, 7mm top dash tray bolts, then lift the OEM tray out, be aware there are 5 clips that will also be retaining the dash tray as you lift up. Release the trim just above the ignition to allow you to pull the the OEM Display/Vent Bezel toward the rear of the car. It is only held in by clips and can be removed by pulling from the vents and working your way around to release the clips. Once released, disconnect the rear connectors attached to the display, terrain, and perimeter alert button if equipped. *If you struggle to get the Vents to clear, put the vehicle in drive to move the column shifter out of the way, don't forget to put it back in park. Next, place the begin to route the USB power cord down through the dash, utilizing the hole nearest to the windshield to begin guiding the cord through. Route the cord towards the passenger side glovebox. Open your glovebox and release the 2 locking tabs to allow it to drop down further. Grab the cord and feed it down to the footwell. You may now guide it towards the center console area easily and connect to a 12v power source of your choosing. Connect to the factory cigarette plug using the included car charger or factory USB outlet. Note: Use Forscan to program the Power Point shutdown timer to be killed when ignition is off and after a door is opened. Turn the vehicle on to send power to the display and test for function. Replace all trim, glovebox, and finally bolt the Display Kit down using the OEM 7mm bolts. Turn the vehicle on to send power to the display. Connect the Display to your phone, the audio setting on the display allows your Bluetooth audio to be sent to the vehicle directly. Your installation is now complete.
Is this compatible with the RubiGrid® from Bulletpoint Mounting Solutions?
- The included Lock-On Grid is compatible with the existing accessories for the RubiGrid® system. The RubiGrid® itself would not be transferred, but rather the accessories to the Lock-On Grid system included with the Display Kit.